kaj
Admin ran out of ideas for a title
Posts : 2510
Join date : 2011-04-17
Age : 50
Location : Fresyes
 | Subject: Re: 91 mr2  Sat Aug 25, 2012 7:30 pm | |
| - react9 wrote:
- who's OP???
and yea i think im a going to auto x it
just gotta get some funds in case shit goes wrong.
that was some heated argument right there 
OP = "original poster" = you. auto-x is pretty simple, though. it's $40 or $45 to run if you not an SCCA member. as long as your car is safe enough for the street, it's safe enough for auto-x. it's all relatively low-speed 1-3rd gear stuff. it's a lot of fun without putting you or your car at high risk. the surfaces are wide open and very safe. you may run over a cone or two. that's about it.  there is an event at the fairgrounds tomorrow. i'm gonna go watch. come out and say hi. i'll be in a white '06 MR. | |
|
react9
noob
Posts : 97
Join date : 2012-03-11
Age : 32
Location : Fresno, CA
| | Subject: Re: 91 mr2 Sat Aug 25, 2012 7:52 pm | |
| - kaj wrote:
- react9 wrote:
- who's OP???
and yea i think im a going to auto x it
just gotta get some funds in case shit goes wrong.
that was some heated argument right there
OP = "original poster" = you.
auto-x is pretty simple, though. it's $40 or $45 to run if you not an SCCA member. as long as your car is safe enough for the street, it's safe enough for auto-x. it's all relatively low-speed 1-3rd gear stuff. it's a lot of fun without putting you or your car at high risk. the surfaces are wide open and very safe. you may run over a cone or two. that's about it.
there is an event at the fairgrounds tomorrow. i'm gonna go watch. come out and say hi. i'll be in a white '06 MR. ok now i know,  yea i tired it with the del sol. it was a rush, it was hella slow though. ill see if i can go i have to work i wont show up with the mr2 though i have a small hole on the tranny! leaks i covered it up with JB weld to bring it home luckily i made it. anyone know if i can weld it or if anyones selling a tranny for it? | |
|
kaj
Admin ran out of ideas for a title
Posts : 2510
Join date : 2011-04-17
Age : 50
Location : Fresyes
| |
react9
noob
Posts : 97
Join date : 2012-03-11
Age : 32
Location : Fresno, CA
| | Subject: Re: 91 mr2 Sat Aug 25, 2012 9:06 pm | |
| - kaj wrote:
- react9 wrote:
ok now i know,
yea i tired it with the del sol. it was a rush, it was hella slow though.
ill see if i can go i have to work i wont show up with the mr2 though
i have a small hole on the tranny! leaks i covered it up with JB weld to bring it home
luckily i made it.
anyone know if i can weld it or if anyones selling a tranny for it?
it's literally a hole? how did that happen? if it just needs a patch, there are quite a few peeps in the area that can weld aluminum. as long as it's not on an important/stress area. and nice that the JB worked to get ya home. ha. being resourceful FTW.
yea its almost the size of a dime. its where the plug to let out the oil is at. on the other side. im not sure what happened im going to take out the tranny and check it out more. fuck yea lol. | |
|
2159ClassicRed
regular
Posts : 373
Join date : 2011-06-20
Location : FresYes
| | Subject: Re: 91 mr2 Mon Aug 27, 2012 11:59 am | |
| - react9 wrote:
- Mynes_3 wrote:
- V6 swap....
sounds nice but wouldnt the weight ratio be compromised? It's been proven, a 4bang-turbo is quicker...............well at least around cones  . Randy Noll's MR2 was a supercharged V6 but later transformed into this beast: [You must be registered and logged in to see this link.]It helps to have a co-driver who works for Garret. | |
|
